We have unearthed the article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the web and reckoned it made sense to relate it with you over here.
Mounting a tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is likewise a moderately challenging job. If the old bathtub is easily easily accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as set in the new one. Ensure you have qualified yourself for the job and fit trying it. As opposed to working with a professional to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly help you mount a brand-new tub in your restroom if you have currently acquired a brand-new tub and do not require to alter the setup of your previous water pipelines.
Your tools and product list ought to comprise the following:
Planning for the Installment
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water and examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the tub should wait until the bath tub has actually been made use of at the very least when as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers are in area in between the faucet and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, leading to complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as installations. They are sold in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in usage. The sealant can split rather very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you enjoyed reading the entire piece. Sharing is caring. Helping others is fun. Thanks for taking the time to read it.
Details Here